Action Instruments Co.
Leesburg, CA 20175
Share:
Action Instruments Signal Conditioners Approved for Use in Hazardous Class I Div 2 Areas
LEESBURG, VA, USA, 1 August 2006 - Action Instruments, a division of Eurotherm, is pleased to announce the signal conditioners now approved for input/output signals from Div 1 hazardous area locations: o The WV408 - DC voltage/current input isolating signal conditioner and o The WV428 - Thermocouple input isolating signal conditioner. Both models can now be installed directly in the Class I, Div...
Read More »Limit Alarm accepts thermocouple input.
Model WV128 dual setpoint limit alarm provides 2 selectable relay output functions. It is powered by 9-30 Vdc and is field configurable via DIP switches for selecting B, E, J, K, R, S, or T thermocouple type. Dual relay alarm outputs can be set as high or low alarms to operate in failsafe or non-failsafe modes. TouchCAL(TM) technology provides electronic stability of microprocessor, enabling 100%...
Read More »Limit Alarm is field configurable.
DIN-rail-mount Model WV108 provides 2 selectable relay output functions. It is powered by 9-30 Vdc and is field-configurable via DIP switches for DC voltages from Ã-
Read More »I/O Modules can be configured as Modbus or ASCII slaves.
I/O Pak(TM) K-Series Modules are 1,000 Hz, 19-bit analog measurement devices. Three types are offered with 1 to 32 channel configurations. All models operate on 10 to 30 Vdc and transmit information over RS-485 interface. I/O configuration files may be stored (on PC), retrieved and downloaded. Linearized, scaled, and formatted data is transmitted to host or network master using standard...
Read More »Modules provide data acquisition and control.
The I/O Pak(TM) DL Series intelligent data logging modules have Modbus, Profibus, and ASCII serial interfaces. They can log data from on-board I/O channels as well as other I/O Pak C-Series and K-Series modules on network. IOPK-DL100-U and IOPK-DL101-U support 8 or 6 universal analog inputs, respectively, while IOPK-DL104-T is dedicated to 4 PT-100 RTD inputs. All support modems, pager messaging...
Read More »I/O Module connects to Modbus or Profibus.
I/O Pak(TM) IOPK-C112-U multifunction module has 4 universal analog input channels, one analog output channel and 2 discrete channels that can be used for inputs or outputs. DIN rail device can be configured for ACSII, Modbus RTU, or Profibus-DP communications. Module's math, logic, control, and diagnostic functions allow it to function as standalone controller or I/O processor, remote I/O for...
Read More »Communications Interface operates using Java applet.
WebView I/O, WVC16 Communications Interface module allows users to view process data on near real-time basis, perform data logging functions on specified modules, calibrate signal conditioners remotely, and view diagnostic information. It can communicate with up to 32 WebView I/O modules by means of its internal infrared communications link, and will notify up to 10 people by e-mail when out of...
Read More »I/O Modules support data acquisition.
Modules in I/O Pak(TM) family include C, K and DL Series. C-Series are 100Hz, 16-bit analog measurement devices with Modbus-RTU, Profibus-DP and simple ASCII communications options. K-Series are 1000Hz, 19-bit analog measurement devices that can be configured as Modbus or ASCII protocol slaves. DL-Series data logging modules with Modbus, Profibus and ASCII serial interface can log data from...
Read More »Action Instruments Signal Conditioners Approved for Use in Hazardous Class I Div 2 Areas
LEESBURG, VA, USA, 1 August 2006 - Action Instruments, a division of Eurotherm, is pleased to announce the signal conditioners now approved for input/output signals from Div 1 hazardous area locations: o The WV408 - DC voltage/current input isolating signal conditioner and o The WV428 - Thermocouple input isolating signal conditioner. Both models can now be installed directly in the Class I, Div...
Read More »Limit Alarm accepts thermocouple input.
Model WV128 dual setpoint limit alarm provides 2 selectable relay output functions. It is powered by 9-30 Vdc and is field configurable via DIP switches for selecting B, E, J, K, R, S, or T thermocouple type. Dual relay alarm outputs can be set as high or low alarms to operate in failsafe or non-failsafe modes. TouchCAL(TM) technology provides electronic stability of microprocessor, enabling 100%...
Read More »Limit Alarm is field configurable.
DIN-rail-mount Model WV108 provides 2 selectable relay output functions. It is powered by 9-30 Vdc and is field-configurable via DIP switches for DC voltages from Ã-
Read More »I/O Modules can be configured as Modbus or ASCII slaves.
I/O Pak(TM) K-Series Modules are 1,000 Hz, 19-bit analog measurement devices. Three types are offered with 1 to 32 channel configurations. All models operate on 10 to 30 Vdc and transmit information over RS-485 interface. I/O configuration files may be stored (on PC), retrieved and downloaded. Linearized, scaled, and formatted data is transmitted to host or network master using standard...
Read More »Modules provide data acquisition and control.
The I/O Pak(TM) DL Series intelligent data logging modules have Modbus, Profibus, and ASCII serial interfaces. They can log data from on-board I/O channels as well as other I/O Pak C-Series and K-Series modules on network. IOPK-DL100-U and IOPK-DL101-U support 8 or 6 universal analog inputs, respectively, while IOPK-DL104-T is dedicated to 4 PT-100 RTD inputs. All support modems, pager messaging...
Read More »I/O Module connects to Modbus or Profibus.
I/O Pak(TM) IOPK-C112-U multifunction module has 4 universal analog input channels, one analog output channel and 2 discrete channels that can be used for inputs or outputs. DIN rail device can be configured for ACSII, Modbus RTU, or Profibus-DP communications. Module's math, logic, control, and diagnostic functions allow it to function as standalone controller or I/O processor, remote I/O for...
Read More »Communications Interface operates using Java applet.
WebView I/O, WVC16 Communications Interface module allows users to view process data on near real-time basis, perform data logging functions on specified modules, calibrate signal conditioners remotely, and view diagnostic information. It can communicate with up to 32 WebView I/O modules by means of its internal infrared communications link, and will notify up to 10 people by e-mail when out of...
Read More »I/O Modules support data acquisition.
Modules in I/O Pak(TM) family include C, K and DL Series. C-Series are 100Hz, 16-bit analog measurement devices with Modbus-RTU, Profibus-DP and simple ASCII communications options. K-Series are 1000Hz, 19-bit analog measurement devices that can be configured as Modbus or ASCII protocol slaves. DL-Series data logging modules with Modbus, Profibus and ASCII serial interface can log data from...
Read More »