Stay up to date on industry news and trends, product announcements and the latest innovations.
Latest New Product News from
Optimal Engineering Systems, Inc.
Used for steppers, DC motors, and servo motor drivers, Joystick Motion Controllers feature three buttons for selecting high, medium and low speed ranges. Featuring 5.5 ft long cord and 25-pin-DB-25, male connector, units come in 4.76 wide x 7.80 in. long footprint. Product is available in one, two, three and four axis models. Speed of motion is controlled by the change in tilt angle of the... Read More
Used to measure angles or rotation of object toÂ precise angular position, 2.362 in. high AK130-15 hasÂ 4.724 in. high center of rotation. Table (4.724 x 5.118 in.)Â offers Â±15Â° of rotation at speeds up to 10Â°/sec and has precision groundÂ worm gear withÂ 304:1 ratio andÂ resolution of 0.0005Â° withÂ 10 micro-step per step stepper motor driver. This and crossed roller... Read More
Offering 360Â° rotation, 4.587 x 3.150 in. AR59-AVÂ employs 180:1 precision worm drive and deep grove ball bearingsÂ to provideÂ Â±0.001Â° resolution when microstepping. Table parallelism is <50 Âµm, and 1.181 in. clear aperture allows for vacuum/electrical lines as well as optics. Replaceable with optical encoder for position verification, knob on motor shaft allows manual... Read More
Along with 3 axes, each featuring 360Â° rotationÂ andÂ 10Â°/sec travel speed, AU300-XZ hasÂ rigid aluminum alloy frame that handles loads to 22.5 lb.Â Low-backlash worm gear drivesÂ as well asÂ precision V groveÂ and cross roller bearings for each axisÂ enable 3.6 arc sec resolutionÂ as well asÂ 18 arc sec repeatability and positional accuracy. Frame hasÂ 11.8 x 11.8 in.... Read More
Constructed of black-anodized aluminum alloy, AZ60-A non-cantilevered moving wedge vertical elevator stage supportsÂ up to 15.43 lb loads without loss of parallelism. Dimensions are 183.7 x 80 x 38 mm (~42 mmÂ when raised), 60Â x 95 mm drilled and tapped stage hasÂ 4 mm vertical travel, and travel speedsÂ reach 2.5 mm/sec. Design provides smooth, straight (to <5 Âµm), vertical motion... Read More
Measuring 160 x 160 x 100 mm, Motorized Goniometer Stage offers solution for precise measurement of angles or rotation of object to precise angular position. Unit provides Â±15Â° of rotation at speeds to 10Â°/sec, 400:1 worm gear ratio, and resolution of 0.0005Â° with 10 micro-step per step stepper motor driver. Height of rotation center at 139 mm is suited for crystallography, light... Read More
IncorporatingÂ power supplies, motion controller, andÂ micro-stepper/servo motor drivers, Sonata series supports up to 3 axes of motion in any combination of steppers, DC servo and brushless servo motors, and voice coil motors. Interface terminal lets operator interact with motion controller without additional PC, and system can also be operated using analog joystick orÂ trackball. Using... Read More
Constructed ofÂ black anodized aluminum alloy, Model AT10-120 features 3.54 in. profile and 8.7 x 5.5 in. drilled and tapped platform with vertical travel of 4.3 in. twin lead precision ground screw and 6 guide rails provide smooth, flat, vertical motion with resolution to 5 Âµ (non-microstepping) and 0.50 Âµ (10 Microstep Driver). Repeatability is 10 Âµ at travel speeds of 5 mm/sec.... Read More
Based on MCU that can be reprogrammed for application, 3.00Â x 3.00Â x .85 in. PH-ET PickÂ and Hold modules operate onÂ singleÂ supply from +9 to +50 Vdc and are suited for driving solenoids, valves, relays, actuators, DC motors, hydraulics, electromagnets, and LEDs. Holding current is 4 A RMS withÂ peak (Pick) current of 15 A for high force/acceleration. Higher current and voltages... Read More
Allegro Series consists of stand-alone RS232, joystick, and trackball interfaced motion controllers. Each system integrates power supplies, indexer, micro-stepper drivers, and step motors. Operator may use joystick, trackball, or GUI to move mechanism to different positions, and can receive, save, edit, and download position information. User may also compose motion profile using BASIC like... Read More
Other Company News from
Optimal Engineering Systems, Inc.